Welcome, Guest. Please login or register.

Recent Posts

Pages: 1 ... 8 9 [10]
91
General Questions / Bug Status-Interfaces-WAN interface
« Last post by Qinn on July 04, 2016, 04:27:58 PM »
Hi Andy thanks for all the good work!

After you use the Disconnect on the WAN interface on the Status-Interfaces page, there is no (Re)connect and you'll have to go Interfaces-WAN and save the settings on the WAN interface to get it up again.
92
Firewall/NAT / Re: Manually add/change firewall rulles
« Last post by Qinn on July 04, 2016, 02:56:00 PM »
Stupid me, in pfsense when you go to hybrid mode the default NAT rule for all interfaces is maintained in t1n1wall I had to create one for every interface

so I had to add for LAN

Interface= WAN
Source= 192.168.1.0/24
Destination=*
Target=*

It would be nice if you could select the source like the type in the firewall and not have to type ip's  ;)
93
Firewall/NAT / Re: Manually add/change firewall rulles
« Last post by Qinn on July 04, 2016, 12:05:40 PM »
I've experimented with pfsense and got it right. In pfsense there is the option "Hybrid Outbound NAT rule generation (Automatic Outbound NAT + rules below)" and I added the Rule as below:

Interface= WLAN
protocol= any
Source= any
Destination= network
Destination network for outbound NAT mapping= 192.168.5.71/32
Translation address= Interface address
Destination port= *

I tried the outbound settings in T1n1wall, but can't seem to get it right. Do I miss something?

94
General Questions / net6501 upgrade to 1.10.2b102 broken
« Last post by rpsmith on May 07, 2016, 08:52:54 PM »
Tried to upgrade my Soekris net6501-50 from a working 1.82b78 to 1.10.2b102 and received the following error: see attached file

Also, tried a fresh install awhile back and it failed as well but I didn't save a copy of the serial port output.

Regards, Roy...
95
Firewall/NAT / Re: Manually add/change firewall rulles
« Last post by Qinn on May 06, 2016, 02:27:07 PM »
Ofcourse, I want to access an ipcam (192.168.5.71) from a machine (192.168.1.100) that resides in another private subnet. In t1n1wall both subnets are assigned interfaces (NIC's) with 192.168.1.1/24 and 192.168.5.1/24 (so no VLAN's). The DHCP server on both interfaces only respond to reserved clients listed.

As said in my previous post by default the ipcam seems to block all access from any different subnet and as the webserver from the ipcam has no option to edit the firewall settings/rules and there is no Telnet/SSH port to access the OS of the ipcam, only IP masquerade (my 2 cents ;) ) came into mind as a possible solution. Hope this helps, thanks for your time.

96
Services / Re: Anyone using mobile IPsec?
« Last post by Gilgamoth on April 26, 2016, 09:28:10 AM »
Hi Andy,
My Mobile IPsec config that works under 1.8, didn't work when I moved to 1.10 (as per my bug report). I use it very rarely, so didn't spend too long testing the 1.10 problem as I was having other issues (as per bug report ;) ).
97
Services / Re: Anyone using mobile IPsec?
« Last post by andywhite on April 24, 2016, 10:02:07 PM »
mobile ipsec (not l2tp) should work fine, the bug that caused the problem was fixed.  If it's not working for you, please post some details
98
Firewall/NAT / Re: Manually add/change firewall rulles
« Last post by andywhite on April 24, 2016, 10:00:11 PM »
you need to setup a NAT rule,  can you give more detail about ip ranges and network setup ?
99
Services / Re: Anyone using mobile IPsec?
« Last post by Gilgamoth on April 18, 2016, 07:47:41 PM »
Has this been tested as working yet? I've just upgraded to 1.10.2b102 and got it stable and tried mobile IPsec for the first time in a long time and it doesn't seem to be working.
100
Firewall/NAT / Manually add/change firewall rulles
« Last post by Qinn on March 29, 2016, 01:45:07 PM »
Hi there, is it possible to manually add a firewall rule?

Why? Well I my case I need to ping a machine that's on a different (private)subnet. Easy you could say, but this machine blocks requests when they aren't coming from the same subnet. Alas there is no telnet\SSH access, so no way for me to change it's set of firewall rules.

So, I want to try address spoofing with something like "iptables -t nat -A POSTROUTING -p icmp -j SNAT --to-source ipaddress"

and test it with a ping, but then I need to manually add/insert a rule, any help is appreciated.
Pages: 1 ... 8 9 [10]