Welcome, Guest. Please login or register.

Recent Posts

Pages: 1 2 [3] 4 5 ... 10
21
General Questions / Re: using t1n1wall for just a captive portal?
« Last post by Domojamana on October 18, 2017, 05:06:56 AM »
 install, you can just update the image.  If you have 1.34 installed, you need 1.34a to up
22
Installation / Re: What are the system requirements?
« Last post by Domojamana on October 18, 2017, 05:06:04 AM »
 install, you can just update the image.  If you have 1.34 installed, you need 1.34a to up
23
Installation / Re: APU4c2 1.10.2b102 vs 2.11.1b140
« Last post by andywhite on August 27, 2017, 11:59:25 PM »
What were the issues you encountered ?
24
Installation / Re: APU4c2 1.10.2b102 vs 2.11.1b140
« Last post by MBehr on August 15, 2017, 08:09:15 PM »
Finally got 2.11.1b140 built on Sat Feb 18 18:30:49 GMT 2017 installed and working after starting completely from scratch. IPv6 (6to4)  [works on 1.10.2b102] is NOT enabled - still a slew of problems - mainly hanging the web access and being unresponsive for any traffic.

So far I am pleased with the M0n0wall -> Smallwall -> t1n1wall migration, as the old Soekris net5501 max throughput was around 88Mbps on the 100Mb nics; the new 1Gb nics in the APU4c2 allow me to easily push my current 100Mbps/10Mbps (217-133 Mbps Down/11Mbps Up).

25
Installation / APU4c2 1.10.2b102 vs 2.11.1b140
« Last post by MBehr on August 10, 2017, 12:21:38 PM »
Managed to get t1n1wall 1.10.2b102 installed and configured for IPv6 (6to4) - would ideally like to get native IPv6 installed and working. Tried with 2.11.1b140 - but I had to keep disabling pf in order to gain access to the web interface - must be something in the config file (that works fine on 1.10.2b102 but mungs up 2.11.  Only issue on 1.10 is LAN DHCP server "Only respond to reserved clients listed below" does not work.

So far I have maximum throughput - so everything seems to be working for 1.10 at the moment (except reservations). Trying to figure out IPv6 is like pulling teeth - especially when trying to match up terms and settings.

If you want feedback on installing and configuring 2.11 and trouble shooting logs etc. let me know, and I'll give it another go.
26
General Questions / Re: Trouble with IPv6
« Last post by MBehr on August 09, 2017, 12:19:07 PM »
Well I finally figured out a workaround - went to the console after enabling IP6, and disabled pf duh. Attempting to configure for IPv6 (DHCP-D) or (6to4). Something's up, not sure what. Ask for diagnostic additional information and I'll try to trouble shoot, as it seems there's still something amiss...just not sure how to tell for sure, appears to be running...testing further.
27
General Questions / Trouble with IPv6
« Last post by Lee Sharp on August 02, 2017, 04:01:49 PM »
Hey Andy!  I recommended t1n1wall to one of my users for support for his apu, and it is working for him but...  When he enables IPv6, it all goes sideways.  He tried to post but was having trouble signing up.  His thread is here.  http://smallwall.freeforums.net/thread/148/apu2c4  and his problem follows.

-----

So I finally managed, after an arduous process, to get t1n1wall running on the APU2c4. Only one tiny problem so far, besides cosmetics (icon beside DHCP leases to add to reservations is missing, tho the link works). Here's the only major problem today for 2.11.1b140 built on Sat Feb 18 18:30:49 GMT 2017:

Can't enable IP6 - doing so locks up t1n1wall and I have to reset everything via the console and restore saved configuration. I've tried straight from initial configuration with no configurations other than out of box and still no go.

Enable IPv6 support
After enabling IPv6 support, configure IPv6 addresses on your LAN and WAN interfaces, then add IPv6 firewall rules.
Note: you must set an IPv6 address on the LAN interface for the IPv6 support to work.

Of course I had IP6 enabled on SmallWall 1.8.4b11 built on Thu Jun 23 17:11:56 CDT 2016 without problem. Here's t1n1wall 2.11.1b140 built on Sat Feb 18 18:30:49 GMT 2017 status.php - interfaces section:

igb0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=6403fb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,POLLING,VLAN_HWCSUM,TSO4,TSO6,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6>
ether 00:0d:b9:46:3d:a8
inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255
inet6 fe80::20d:b9ff:fe46:3da8%igb0 prefixlen 64 scopeid 0x1
nd6 options=61<PERFORMNUD,AUTO_LINKLOCAL,NO_RADR>
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
igb1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=6403fb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,POLLING,VLAN_HWCSUM,TSO4,TSO6,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6>
ether 00:0d:b9:46:3d:a9
inet6 fe80::20d:b9ff:fe46:3da9%igb1 prefixlen 64 scopeid 0x2
inet x.x.x.x netmask 0xfffffe00 broadcast 255.255.255.255
nd6 options=61<PERFORMNUD,AUTO_LINKLOCAL,NO_RADR>
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
igb2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=6403fb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,POLLING,VLAN_HWCSUM,TSO4,TSO6,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6>
ether 00:0d:b9:46:3d:aa
inet 10.0.0.1 netmask 0xffffff00 broadcast 10.0.0.255
inet6 fe80::20d:b9ff:fe46:3daa%igb2 prefixlen 64 scopeid 0x3
nd6 options=61<PERFORMNUD,AUTO_LINKLOCAL,NO_RADR>
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
enc0: flags=41<UP,RUNNING> metric 0 mtu 1536
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
groups: enc
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
groups: lo
pflog0: flags=100<PROMISC> metric 0 mtu 33184
groups: pflog


Would have posted on t1n1wall forum, but registering to post there doesn't seem to be working atm...so here I am. Need to be pointed in the right direction to help diagnose/enable IP6.

Thanks to your previous help I've gotten this far...just about there.
28
Installation / Re: t1n1wall on APU3a2 ??
« Last post by kairuri on March 18, 2017, 05:03:23 AM »
Hmmm, I know that the BIOS is an issue - PCengines have only just advertised that boot from SD card was possible with their latest BIOS, but I am using the latest BIOS advertised on their  APU3a2 page.  I'll keep an eye on the page.
I guess that it will be possible in the "near future" - I see that they have later BIOS advertised on their APU2 pages, but I'm not sure of the compatibility.

I'm happy for the timebeing :) even if mSATA is somewhat overkill

I am really pleased in the increase in performance over the ALIX board - not just slightly faster!  I have a 100Mb fibre connection to my house (GPON using PPPoE over VLAN10) which will give me gigabit to my house if I pay the ISP more...

BTW thanks for all the work on t1n1wall! I am quite a long time user of m0n0wall->smallwall->t1n1wall - I have moved to t1n1wall as it appears to be moving towards later freeBSD distros that have more chance of supporting later APU hardware.
29
Installation / Re: t1n1wall on APU3a2 ??
« Last post by andywhite on March 17, 2017, 09:15:09 PM »
Hi

Googling

Timeout at sdcard_waitw:162

Gives results that indicate your bios needs an update,  perhaps that will help solve the original problem ?
30
Installation / Re: t1n1wall on APU3a2 ??
« Last post by kairuri on March 16, 2017, 09:55:06 PM »
Hi,
There is an obvious workaround that I have now implemented - install t1n1wall to the mSATA card directly with the APU booted from a USB.  I am very pleased with the result.  Here's a quick and dirty installation instruction:

From a linux desktop (or any other UNIX, but you will need to adapt device names and fdisk -l)
# wget http://downloads.yawarra.com.au/osimages/voyage0.10.0_8GB_APU.img.gz
/dev/sdd is an 8GB USB stick
# zcat voyage0.10.0_8GB_APU.img.gz |dd of=/dev/sdd bs=4M
# mount /dev/sdd1 /mnt
# cp t1n1wall/generic-pc-2.11.1b140.img /mnt/root/
# umount /mnt

Boot the APU from this USB stick and install t1n1wall to mSATA disk from USB using serial console
find APU disk devices
# fdisk -l | more
# cd /root
# zcat generic-pc-2.11.1b140.img | dd of=/dev/sda bs=16k
# sync && reboot

You will need to set up the interfaces from the serial console as required
For a serial console I use minicom running from a linux virtual console (Ctrl-Alt-F1)

Cheers
Pete
Pages: 1 2 [3] 4 5 ... 10