Welcome, Guest. Please login or register.

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - andywhite

Pages: 1 2 3 [4] 5 6 ... 8
46
Installation / Re: Possible DHCP error
« on: March 03, 2016, 02:11:31 PM »
damn, ok , I think i'll have to look at patching dnsmasq :( , I reported a bug, but I don't think I'll hear of a fix soon, so will have to look at fixing it ...

Thanks for testing !

47
Installation / Re: Possible DHCP error
« on: March 03, 2016, 09:51:35 AM »
I'm hoping this is fixed in b98 , if you can test please...

48
General Questions / Re: Can't generate certificate
« on: March 03, 2016, 12:11:45 AM »
that error is a bit misleading, it happens if you system date is < the firmware build date - 24h

you can check by executing 'date +%s' from exec.php and comparing to executing 'cat / etc / version.buildtime.unix'

but it also is the error when the cert generation failed (for any reason !) , i'll take a look

49
Installation / Re: Possible DHCP error
« on: March 02, 2016, 06:18:54 PM »
thanks, I look at the status.php see what needs to change.

i took a quick look, this is a bug in dnsmasq, that syntax is correct upto version 2.65 of dnsmasq, but 2.66 introduced a change that is behind this error.

I think we can work around it by adding the subnet mask at the end like this

Code: [Select]
dhcp-range=set:opt2,192.168.5.10,192.168.5.20,static,255.255.255.0
the 'static' parameter , is the mode of operation for the range, i.e. only issue static addresses.  I'll try look later see if that workaround will address the problem.


50
Installation / Re: Possible DHCP error
« on: March 02, 2016, 12:25:02 PM »
Thanks for the report, I'll take a look .

ISC dhcpd was replaced with dnsmasq recently, and thats where this bug came from i'm sure.  should be a quick fix

51
Hardware / Re: ALIX boards, max throughput?
« on: March 01, 2016, 02:48:35 PM »
if by QOS you mean the traffic shaper, it should work fine.

are you using 1.10 ? have you tried enabling fastforward to see if it makes any difference ?

the heat on the APU is distributed through the bottom of the case, it acks as a heat sink.  mine is warm, but so is my cable modem :)  there are some discussions on the internet around APU heat where people did various tests, which will have better data !

52
Hardware / Re: ALIX boards, max throughput?
« on: February 29, 2016, 09:59:53 PM »
oops, yes I meant APU , sorry !

ALIX, the nics are only 100Mbps, so 80-90 Mbps sounds right as the maximum throughput

53
Installation / Re: Which file for embedded fresh install
« on: February 29, 2016, 09:58:21 PM »
if you imaging direct to the card that will be in the system , then  xxx-serial

if you are imaging to a usb stick that you will boot from, then install from the usb to the internal storage, use  xxx-serial-installer

54
Firewall/NAT / Re: NAT/Port forwarding totally broken?
« on: February 29, 2016, 10:33:06 AM »
Hi, your problem reads differently, in that it works sometimes and not others.  Original reporter can't get it to work at all ....

just an FYI,  1.10.x release is based on freebsd 10.  freebsd , while having a lot of changes, also is on ipfilter 5.  Why am I calling this out ?  There was/is a bug in ipv6 stateful inspection , this took >2 months to figure out the issue, working with the ipfilter maintainer.  It turned out to be a freebsd 10 change with packet checksums, and not an ipfilter 5 problem.  It was very frustrating :(  pf didn't have the problem, as pf doesn't check checksums like ipfilter , which made us look at ipfilter for too long ...

There are mixed reports of ipnat issues in freebsd 10 / ipfilter combinations , but none with any real data to help track down the issue.  They are mostly about ipnat having problems after several days, and a reboot fixing it, I experienced this intermittantly, but haven't since patching for the ipv6 issue several months ago. 

I use t1n1wall 1.10.x at home on ALIX, behind a cable modem, and don't see these issues.  I have plenty of ports forwarded, and I have nightly backups to the internet that don't fail.

What does all this mean ?  I'm going to need you help to track this down and troubleshoot, and your patience

55
General Questions / Re: What dyn-dns do you use?
« on: February 27, 2016, 04:00:20 PM »
They can be updated with a fetch without a username password.  So a scheduler task making the fetch should work fine.

56
General Questions / Re: How does Version Checking work?
« on: February 27, 2016, 03:58:25 PM »
Hi.   It looks broken.

It works by:

When you open that page it calls out to t1n1wall.com and pass the version in use.   The server responds if that is the latest or not.   It looks like that part on the server is broken.  I'll take a look.  I think it needs rework. 

57
Firewall/NAT / Re: NAT/Port forwarding totally broken?
« on: February 24, 2016, 09:30:09 AM »
I don't see any reports of this,  and I too have plenty working.  Please add more data

58
General Questions / Re: Multi-core support?
« on: February 24, 2016, 09:27:36 AM »
It has support multi cores since 1.8.x,  so there should be no issues with using multiple cores

59
Hardware / Re: ALIX boards, max throughput?
« on: February 24, 2016, 09:25:25 AM »
When I first got an alix I tested server to server copies lan to wan and got > 800Mbps at about 80% CPU. 

POLLING and TSO should reduce cpu,  but some nics don't work right with these features enabled. TSO on the alix works fine afaik.

There is also fastforwarding available in advanced options that reduces latency and cpu.  It's not enabled by default as it may break some ipsec things and hasn't had extensive testing in t1n1wall yet

My broadband is 240mbps and at peak I get full speed at <30% CPU

60
Feature Requests / Re: BlinkLED
« on: February 24, 2016, 09:18:16 AM »
I think it's personal taste.  The existing method gives the same information by flashing the LEDs at different speeds.

If enough people thought it useful I'd consider it.   Also you could consider graphing it with snmp and setting up alerts with external tools. 

Pages: 1 2 3 [4] 5 6 ... 8